Difference between revisions of "BeagleBone Black"
(→First Boot) |
(→Add a WiFi adapter) |
||
Line 163: | Line 163: | ||
You have got a new IP address for the WiFi interface. Note it, most accesspoints re-issue the same IP address if the device reconnects frequently - otherwise it may be an idea to consult the accesspoint to see if it is possible to configure that a specific MAC addresse is connected to a specific IP addresse often it is possible. | You have got a new IP address for the WiFi interface. Note it, most accesspoints re-issue the same IP address if the device reconnects frequently - otherwise it may be an idea to consult the accesspoint to see if it is possible to configure that a specific MAC addresse is connected to a specific IP addresse often it is possible. | ||
− | Now in order to check if the WiFi comes up automagically after a reboot reboot the system. | + | Now in order to check if the WiFi comes up automagically after a reboot perform a reboot of the system. |
Sometime my BBB does not get an IP address. After digging into the log files I found that the driver does not always get the device ready for DHCP'ing in time. | Sometime my BBB does not get an IP address. After digging into the log files I found that the driver does not always get the device ready for DHCP'ing in time. |
Revision as of 13:48, 1 May 2015
Find below my experiences with the BeagleBone Black (BBB) revision 3.
Contents
First Boot
First boot with BeagleBone Black is best done by using a serial communication program like CuteCom or Putty.
Attach the USB connector to your PC and issue this command to find the tty-port that will be created:
$ ls -lart /dev
drwxr-xr-x. 2 root root 80 Aug 16 13:19 bsg crw-rw----. 1 root disk 21, 1 Aug 16 13:19 sg1 drwxr-xr-x. 2 root root 3900 Aug 16 13:19 char drwxr-xr-x. 22 root root 3560 Aug 16 13:19 . brw-rw----. 1 root disk 8, 16 Aug 16 13:19 sdb drwxr-xr-x. 6 root root 120 Aug 16 13:19 disk drwxr-xr-x. 2 root root 200 Aug 16 13:19 block crw-rw-rw-. 1 root dialout 166, 3 Aug 16 13:19 ttyACM3 crw-rw-rw-. 1 root tty 5, 0 Aug 16 13:20 tty crw-rw-rw-. 1 root tty 5, 2 Aug 16 13:21 ptmx
The above list show the devices created when attaching the USB cable. The line of interest here is the ttyACM3 - might differ on other systems.
Since normal users normally not are member of the dialout group the quickest way to gain access to the tty-port is to issue this command:
$ sudo chmod o+rw /dev/ttyACM3
This will give a normal user access to the port.
Alternatively modify the /etc/group to allow the login to be member of the dialout group.
Now open the CuteCom or Putty port on a serial line using /dev/ttyACM3 and 115200 bps as settings.
An output like this can be seen:
Login timed out after 60 seconds. \0x1b[r\0x1b[H\0x1b[J Debian GNU/Linux 7 kolles-beaglebone ttyGS0 default username:password is [debian:temppwd] Support/FAQ: http://elinux.org/Beagleboard:BeagleBoneBlack_Debian The IP Address for usb0 is: 192.168.7.2 kolles-beaglebone login:
Now login using the defaults given.
Also try to issue
$ ssh debian@192.168.7.2
This will open an ssh connection over the USB cable, which also supports networked traffic, to the BBB.
Add a WiFi adapter
If you are going to add a WiFi adapter you should search eBay or Alibaba for a Realtek RTL8188CUS or similar adapter. They will usually work right out of the box without any external power.
Plug in the adapter into the USB interface.
Issue
]$ lsusb
expect a result like this
root@beaglebone:~# lsusb Bus 001 Device 002: ID 0bda:8176 Realtek Semiconductor Corp. RTL8188CUS 802.11n WLAN Adapter Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Next issue
root@beaglebone:~# ifconfig -a
expect something like this output
eth0 Link encap:Ethernet HWaddr 1c:ba:8c:e7:40:03 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:40 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:65536 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) usb0 Link encap:Ethernet HWaddr f6:7f:36:73:b5:93 inet addr:192.168.7.2 Bcast:192.168.7.3 Mask:255.255.255.252 inet6 addr: fe80::f47f:36ff:fe73:b593/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:774 errors:0 dropped:0 overruns:0 frame:0 TX packets:540 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:62696 (61.2 KiB) TX bytes:94951 (92.7 KiB) wlan0 Link encap:Ethernet HWaddr 00:13:ef:20:06:33 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:5 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
From this we can see that the WiFi adapter was recognised by the Linux OS and given the device name wlan0.
In order to have the wiFi to auto connect at boot time issue
root@beaglebone:~# vi /etc/network/interfaces
In this file uncomment the lines following the #WiFi example
auto wlan0 iface wlan0 inet dhcp wpa-ssid "YourSSID" wpa-psk "YourVerySecretPassword"
save the file and execute this command
]$ ifconfig wlan0 up
This will start the wlano, but nothing is output for your information.
Issue
]$ ifup wlan0
This will give you an output like the one shown below
ioctl[SIOCSIWAP]: Operation not permitted ioctl[SIOCSIWENCODEEXT]: Invalid argument ioctl[SIOCSIWENCODEEXT]: Invalid argument Internet Systems Consortium DHCP Client 4.2.2 Copyright 2004-2011 Internet Systems Consortium. All rights reserved. For info, please visit https://www.isc.org/software/dhcp/ Listening on LPF/wlan0/00:NN:NN:NN:NN:NN Sending on LPF/wlan0/00:NN:NN:NN:NN:NN Sending on Socket/fallback DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 7 DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 12 DHCPREQUEST on wlan0 to 255.255.255.255 port 67 DHCPOFFER from 192.168.10.1 DHCPACK from 192.168.10.1 bound to 192.168.10.110 -- renewal in 35998 seconds.
You have got a new IP address for the WiFi interface. Note it, most accesspoints re-issue the same IP address if the device reconnects frequently - otherwise it may be an idea to consult the accesspoint to see if it is possible to configure that a specific MAC addresse is connected to a specific IP addresse often it is possible.
Now in order to check if the WiFi comes up automagically after a reboot perform a reboot of the system.
Sometime my BBB does not get an IP address. After digging into the log files I found that the driver does not always get the device ready for DHCP'ing in time.
I stumbled upon this on AdaFruit.
]$ apt-get update && apt-get install git ]$ git clone https://github.com/adafruit/wifi-reset.git ]$ cd wifi-reset ]$ chmod +x install.sh ]$ ./install.sh
after installing this the BBB always come up on WiFi - but sometimes it takes minutes to get everything registered and running.
Yocto Project
The Yocto Project, see the home page for further details, can create a distribution for the BBB.
For instructions on how to build a personal Yocto Project Distribution see Yocto Project Build Instructions.
Creating the boot SD
There are several methods to create a bootable SD card.
The easiest way is to use a graphical interface, e.g. gparted
Create two partitions, one size 40, or more, megabytes for u-boot and one for the rest of the SD card - here 7+ GB.
Label the boot partition boot and the other partition root.
The boot partition shall be a primary partition of type FAT32 while the rest is a ext3 or ext4 file system. Format the partitions to the designated file system types and set the boot flag for the boot partition.
Alternative method
Here is an alternative method only using the console if no graphical environment is available:
$ export DISK=/dev/sdc $ umount ${DISK}1 #<<<Note the addition of the '1' $ sudo dd if=/dev/zero of=${DISK} bs=512 count=20 $ sudo sfdisk --in-order --Linux --unit M ${DISK} <<-__EOF__ 1,12,0xE,* ,,,- __EOF__ $ sudo mkfs.vfat -F 16 ${DISK}1 -n boot $ sudo mkfs.ext4 ${DISK}2 -L rootfs
Here's whats happening:
- Provided that the newly inserted SD card is /dev/sdc - could be another e.g. sdb depending on the disks in the PC - tell the rest of the script where the device is located (the DISK variable)
- unmount if automount mounted it
- dd is a very effective utility to create files and much more - here zeros is copied from /dev/zero (if=/dev/zero) to the disk (of=${DISK} i.e. /dev/sdc) with 512 bytes block size (bs=512) for 20 blocks (count=20)
- Next rather than calling the fdisk the sfdisk partition table manipulating program is used with a HERE script (the part from __EOF__ to __EOF__)
- With the partition the next is to make a file system with mkfs both vfat and ext4 file systems and at the same time labelling the partitions
Transfer binaries to the SD card
Mount the two SD card partitions. On some Linuxes it is easily done by removing the SD card and reinsert it and automount will automagically mount the disk partitions.
From the Yocto Project distribution copy the MLO and the u-boot.img files to the boot partition.
In order to populate the root file system to the root partition untar the compressed root file system that bitbake produced.
$ cd <the mounted root partition> $ sudo tar xf <path to poky>/beaglebone/tmp/deploy/images/beaglebone/core-image-sato-beaglebone.tar.bz2 . $ sync
This is what is happening:
- First change to the root partition on the SD card (on Fedora it is typically mounted /run/media/<username>/root)
- Then untar the compressed root file system from where bitbake built it (here it is the graphical core-image-sato distribution)
- Finally issue sync to let the kernel write everything to the SD card - when sync returns unmount the SD card.
Windows and Mac users
You will have to figure out from the descriptions above how to format and create the filesystems on the SD card and how to copy the files to the card.
Booting the BBB with Yocto Project
Insert the SD card into the slot for it on the BBB. Press and hold the button on top of the board near the SD card in order to boot from the SD (otherwise the BBB will boot from the built in eMMC). Apply power through the USB connector.
Monitor the boot process
Only if the u-boot causes problems a serial connection may be helpful, otherwise it is usually enough to wait until the USB interface becomes available in the boot process.
So if the u-boot messages should not be monitored, just connect the USB cable to the PC and start the favourite serial communication program, e.g. CuteCom, Putty or screen. Wait until the tty USB device becomes available. The USB interface will become available when the system is near the end of the boot process - and at that time the u-boot messages are long gone.
If, for some reason, the board won't boot, a serial cable need to be connected to the board. Get a PL2303 cable - or build one your self...
Connect the serial cable to the port to J1 as shown below.
PL2303 USB to serial cable
Board Wire Function Pin 1.....Black.....Ground Pin 4.....Green.....Receive Pin 5.....White....Transmit (Where pin 1 is the one near the white dot)
Connecting the pl2303 cable to the BeagleBone Black
Stop u-boot
Using a serial interface it is possible to monitor the boot process.
Here the command
$ screen /dev/ttyUSB0 115200
is used to connect to the serial line (use Ctrl-a+k to kill the window). Putty or CuteCom can show the same.
Immediately after applying power and e-boot presents it self on the serial interface, hit any key on the keyboard to stop the boot process.
This is a typical output from the early boot process:
U-Boot SPL 2014.04-00014-g47880f5 (Apr 22 2014 - 13:23:54) reading args spl_load_image_fat_os: error reading image args, err - -1 reading u-boot.img reading u-boot.img U-Boot 2014.04-00014-g47880f5 (Apr 22 2014 - 13:23:54) I2C: ready DRAM: 512 MiB NAND: 0 MiB MMC: OMAP SD/MMC: 0, OMAP SD/MMC: 1 *** Warning - readenv() failed, using default environment Net: <ethaddr> not set. Validating first E-fuse MAC cpsw, usb_ether Hit any key to stop autoboot: 0 U-Boot#
Here the u-boot has stopped and are awaiting a command.
Enabling the DS18B20 thermometer
The version of Debian that my board was supplied with uses the Flattened Device Tree in order to ease the access to GPIO's and other hardware. This are so for the most modern Linux distributions for the ARM processors. The reason for this is mainly because Linus Thorvalds did not want to include the large amount of device drivers for the ARM processor family in the kernel. Se more about the Flattened Device Tree (FDT) on this site.
From this site I was inspired to set-up the correct dts file enabling the usage of GPIO pin 2 for the 1Wire interface.
Create a file name DS1820-00A0.dts with this content
/dts-v1/; /plugin/; / { compatible = "ti,beaglebone", "ti,beaglebone-black"; part-number = "DS1820"; version = "00A0"; exclusive-use = "P9.12"; fragment@0 { target = <&am33xx_pinmux>; __overlay__ { ds1820_pins: pinmux_ds1820_pins { pinctrl-single,pins = <0x78 0x37>; }; }; }; fragment@1 { target = <&ocp>; __overlay__ { onewire@0 { status = "okay"; compatible = "w1-gpio"; pinctrl-names = "default"; pinctrl-0 = <&ds1820_pins>; gpios = <&gpio2 28 0>; }; }; }; };
Compile the specification into a dtbo binary file
dtc -O dtb -o /lib/firmware/DS1820-00A0.dtbo -b 0 -@ DS1820-00A0.dts
Finally in order to enable this part of the device tree perform at every boot this command
echo DS1820 > /sys/devices/bone_capemgr.*/slots
The thermometer should now show up in the /sys/bus/w1/devices folder
drwxr-xr-x 2 root root 0 Jan 1 2000 . drwxr-xr-x 4 root root 0 Jan 1 2000 .. lrwxrwxrwx 1 root root 0 Feb 21 10:49 28-000005a7ce64 -> ../../../devices/w1_bus_master1/28-000005a7ce64 lrwxrwxrwx 1 root root 0 Feb 21 10:49 w1_bus_master1 -> ../../../devices/w1_bus_master1
the 28-00000nnnnnnn is the thermometer - they are all uniquely identified, so the n's will vary.
Test with Python
To check that the thermometer work correct prepare this short test program in a file named test.py where you of course will adjust the thermometer ID to suit your set-up:
import time w1="/sys/bus/w1/devices/28-000005a7ce64/w1_slave" while True: raw = open(w1, "r").read() print "Temperature is "+str(float(raw.split("t=")[-1])/1000)+" degrees" time.sleep(1)
Execute the program
python test.py
you should get something similar to this
root@klaus-BBB:~/ds18b20# python test.py Temperature is 24.0 degrees Temperature is 24.0 degrees Temperature is 24.062 degrees Temperature is 24.062 degrees ^CTraceback (most recent call last): File "test.py", line 8, in <module> time.sleep(1) KeyboardInterrupt root@klaus-BBB:~/ds18b20#
Test using Bonescript
This source first locates the attached thermometer and then uses it for temperature reading.
This code is only able to handle one thermometer at a time, or in fact only one 1-wire device at at time.
// // Interface for the thermometer // Author : Klaus Kolle // Date : 2015 02 22 // Revision : 0.0.3 var b = require('bonescript'); var f = require('fs'); //console.log('Hello, Thermostate.'); var temperature; // Read from the 1-wire thermometer // The 28-00000nnnnnnn will change depending of the device connected // var oneWireDir; locateThermometer(); function locateThermometer() { var initialDir = '/sys/bus/w1/devices/'; var regExpr = '28-00000'; var dir = []; var i; // Get all files and directories in the dir var dirs = f.readdirSync(initialDir); // Did we gat anything - if not the cape manager is probably not initialised // with the dtbo compiled device tree if (dirs.length > 0) { for (i = 0; i < dirs.length; i++) { // Only select the directories matching the pattern if(dirs[i].match(regExpr)) { dir.push (dirs[i]); } } // Currently the code only accepts one thermometer oneWireDir = initialDir + dir + "/w1_slave"; } } function readTemp() { // Callback function for the timer b.readTextFile(oneWireDir, printTemp); } // The 1-wire returs this when reading the device // klaus@klaus-BBB:~$ cat /sys/bus/w1/devices/28-000005a7ce64/w1_slave // a5 01 4b 46 7f ff 0b 10 f7 : crc=f7 YES // a5 01 4b 46 7f ff 0b 10 f7 t=26312 // Therefore a split is needed. We need the string after the second = function printTemp(x) { // We receive the data i x if (x.data != '') { var stringToSplit = x.data; // Split at = - three resulting strings are returned var arrayOfStrings = stringToSplit.split('='); // We are only interesd in the last temperature = (arrayOfStrings[2]) / 1000; console.log("Temp: " + temperature); } } setInterval(readTemp, 5000);
Expect a readout like this
Temp: 24.687 Temp: 24.75 Temp: 24.75 Temp: 24.687 Temp: 24.75 Temp: 24.75 Temp: 24.75 Temp: 24.687
Development on a PC host and remote debugging
A few things are needed in order to set-up development of programs, that shall execute on an ARM platform. You'll need a cross compiler - a compiler that can generate ARM executable code while the compiler is executed on the PC platform, which is typically a Intel X86_64 architecture.
Cross Compiler
The Fedora package system does not contain a suitable compiler for the ARMv7 processor.
Luckily Linaro, does maintain a toolchain suitable for us. At this point you can find the newest binaries for your operating system. Go up the directory structure to discover if a newer compiler has been released.
The following is suited for Fedora Linux and other Linux'es as they are rather generic.
]$ cd ~/Downloads $] wget http://releases.linaro.org/14.11/components/toolchain/binaries/arm-linux-gnueabihf/gcc-linaro-4.9-2014.11-x86_64_arm-linux-gnueabihf.tar.xz
which will download the newest version on the time of writing this.
I keep downloaded tools in the /opt directory rather than in the /usr/local or other places in the /usr tree.
]$ cd /opt ]$ mkdir toolchains ]$ cd toolchains ]$ tar Jxvf ~/Downloads/gcc-linaro-4.9-2014.11-x86_64_arm-linux-gnueabihf.tar.xz ]$ ln -s gcc-linaro-4.9-2014.11-x86_64_arm-linux-gnueabihf/ gnueabihf ]$ file gnueabihf/bin/arm-linux-gnueabihf-gcc
These commands will create a toolchains directory in /opt and unpack the downloaded binaries into a structure. A symbolic link gnueabihf is created. This link can later be changed if a newer version of the compiler and libraries are downloaded.
The last command is just for ensuring that you've got the correct package downloaded. Expect something like this:
[klaus@klaus-x230 bin]$ file arm-linux-gnueabihf-gcc arm-linux-gnueabihf-gcc: ELF 64-bit LSB executable, x86-64, version 1 (SYSV), dynamically linked, interpreter /lib64/ld-linux-x86-64.so.2, for GNU/Linux 2.6.24, BuildID[sha1]=71722376ff3af9eee5caf7bdfa2ecc350db0a590, not stripped [klaus@klaus-x230 bin]$
Develop a Cross Compiled Program
Start Eclipse and create a new project:
Notice the settings for the Cross GCC
On one of the next dialogues you have to specify what the prefix for the cross compiler tools are and where they resides.
In the project create a new C source file and fill in some "Hello World" stuff.
Save and compile (Ctrl+S, Ctrl+B).
In a console go to <path to your project>/Debug
]$ file <your binary (project name)>
Expect something like this:
[klaus@klaus-x230 Debug]$ file TestRemoteDBG TestRemoteDBG: ELF 32-bit LSB executable, ARM, EABI5 version 1 (SYSV), dynamically linked, interpreter /lib/ld-linux-armhf.so.3, for GNU/Linux 2.6.16, BuildID[sha1]=e8baff7637d637533f3730021407ffdc6d4c314e, not stripped [klaus@klaus-x230 Debug]$
This tells us that the compiler has produced ARM executable code.
Remote Debugging
In order to be able to debug remote the remote board needs a suitable gdbserver. There is one already onboard - or it can be downloaded using apt-get, but that one does not operate correct with the toolchain downloaded previously.
But luckily there is a suitable gdbserver included with the gnueabihf tools.
]$ scp /opt/gnueabihf/bin/gdbserver <username>@<your BBB IP>:~/
If you set-up password-less login over SSH (see this page for details) your life will be much easier.
You can test your newly developed ARM program on your BBB.
]$ scp <path to your project>/Debug/<yourbinary> <username>@<Your BBB IP address>:~
Log on to your BBB and try
]$ ./<yourbinary>
and inspect the output.
Next thing is to set up remote debugging.
In Eclipse select the Run menu and select Debug Configurations
First mark the C/C++ Remote debugging and then click on the new button to the upper left corner of the dialogue.
You'll get a dialogue like this:
Press the New button to the right of the Connection line.
This will open a dialogue for setting up the connection to the BBB. We'll use SSH.
You can use the local IP address or any other configured for the BBB.
Returning to the main Debug Configuration dialogue you'll see that the Connection now has been filled in with the details you just provided.
Next you'll have to specify the complete path of your program to execute on the BBB. The program will be sent over the SSH connection before launching the gdbserver - so any changes made on the development host will be reflected on the binary on the BBB.
Here I just placed the binary in my home directory, but it could be anywhere suitable.
Next thing to do is to click on the Debugger tab in the top of the dialogue. In this part of the settings you'll have to specify a complete path and name of the debugger - in this case we'll use the Linaro supplied residing in /opt/toolchains/gnueabihf
Also click on the Shared libraries tab and click Add and navigate to /opt/toolchains/gnueabihf/libc/lib and add that. This will remove some error messages during debugging.
Adjust the path to the gdbserver on the BBB.
You are now ready to debug. Press the Debug button.
You're asked a password for your login on the BBB.
And the you're told what system you're debugging.
And finally the debugger launches the program that has been transfered to the remote BBB and the gdbserver is launched with the program a a parameter and you can debug you application just like any other application.
This set-up has been heavily inspired by this site and the video by D. Molloy at YouTube.
Installing a new official Debian image on a SD card
Download from the BeagleBoard.org site or elsewhere a fresh image suitable for the BBB.
You will typically get a file named like this
bone-debian-7.8-lxde-4gb-armhf-2015-03-01-4gb.img.xz
Date and version number may vary.
In your download directory execute this command
]$ xz -dk bone-debian-7.8-lxde-4gb-armhf-2015-03-01-4gb.img.xz
this will unpack the image into a file like this
bone-debian-7.8-lxde-4gb-armhf-2015-03-01-4gb.img
Locate your SD card
Have a 4GB SD ready and inserted into your computer. Execute
]$ ll /dev/sd*
or
]$ ll /dev/mmcblk*
the way your computer interface to the SD card will either see it as a disk drive and name it /dev/sdN, where N is the next free letter - e.g. you have one disk already installed in your computer it is most likely sda[09], the next disk the system recognises will be sdb.
On my laptop when I use the SD slot directly in the laptop the system sees the SD card as a new mmc block device, hence the mmcblk name.
Another way to determine the name of the freshly inserted SD card is to execute
]$ ls -lart /dev
this will list the content of /dev in reverse order with the newest at the end of the list, i.e. at the bottom of your console.
Removing the SD card and rerunning the command will give you the final evidence to what the name is, since it is now missing in the list.
If the SD card i preformatted, which most are, you will see two - or more - devices like this
]$ ll /dev/mmcblk* brw-rw----. 1 root disk 179, 0 May 1 13:15 /dev/mmcblk0 brw-rw----. 1 root disk 179, 1 May 1 13:15 /dev/mmcblk0p1 ]$
The mmcblk0 is the main block device and the mmcblk0p1 is the first partition on the disk.
Transferring the image to the SD card
In order to transfer the disk image to the SD card first ensure that it is not mounted, e.g. by removing the card and re-insert it into the reader slot or by running a umount command (RTFM umount).
Next issue this command
]$ sudo dd if=bone-debian-7.8-lxde-4gb-armhf-2015-03-01-4gb.img of=/dev/mmcblk0 bs=1M
The dd command is a versatile utility that takes an input file (if) and an output file (of) and copies the input file to the output file (/dev/mmcblk0) in 1 mega bytes blocks (BS=1M). Expect 10 to 20 minutes before the command returns depending on the speed of your card reader and the SD card. Note here, that we use the main block interface file mmcblk0 not the mmcblk0p1 or the sdb not the sdb1.
When finished you will get a report like this
3700+0 records in 3700+0 records out 3879731200 bytes (3.9 GB) copied, 557.971 s, 7.0 MB/s
and your SD is ready to run in the BBB.
Starting the new image on BBB
Remove the SD card from your computer and insert it into the BBB.
Find the user button located just above the SD card slot.
Press and hold the button while applying power to the device. When the device starts to boot (blinking leds) release the user button.
If you have previously connected your BBB using the
]$ ssh root@192.168.7.2
you will probably get a message like this
]$ ssh root@192.168.7.2 @@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@ @ WARNING: REMOTE HOST IDENTIFICATION HAS CHANGED! @ @@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@ IT IS POSSIBLE THAT SOMEONE IS DOING SOMETHING NASTY! Someone could be eavesdropping on you right now (man-in-the-middle attack)! It is also possible that a host key has just been changed. The fingerprint for the ECDSA key sent by the remote host is 80:98:39:60:af:8e:db:14:47:9f:76:6a:88:89:12:e3. Please contact your system administrator. Add correct host key in /home/klaus/.ssh/known_hosts to get rid of this message. Offending RSA key in /home/klaus/.ssh/known_hosts:49 ECDSA host key for 192.168.7.2 has changed and you have requested strict checking. Host key verification failed.
which tells us that in the ~/.ssh/known_hosts file we keep a fingerprint of hosts that we have previously accepted to be legal computers to connect to. You have to edit the ~/.ssh/known_hosts file and remode the line(s) beginning with 192.168.7.2 and then try to connect once again.
First time you connect to your new image you will be prompted to verify the fingerprint of the connecion. Do that by typing yes.
Determine the version of your new image by issuing this command
root@beaglebone:~# uname -a Linux beaglebone 3.8.13-bone70 #1 SMP Fri Jan 23 02:15:42 UTC 2015 armv7l GNU/Linux root@beaglebone:~#
This is at the time of wirting the latest official supported image, but not necessarily the newest - you may find newer images floating around the Internet. The following device driver development will take outspring in the version.
Developing a device driver for the BBB
This section is heavily inspired by Derek Molloy's fine writing about device driver development.